Force Gage PCE-DFG N 100TW

Availability : in stock


Force Gage up to 100 Nm / External torque transducer 1/2″ internal square / Graphic display / PEAK function / Sampling rate max. 1600 Hz / Incl. Software
The force gage consists of a handheld measuring device and an external torque transducer. The torsion transducer is connected to the hand-held device via a 1.5 m / 4.9 ft long cable and thus enables installation in a test stand or direct assembly on a test bench.
The force gage is delivered adjusted so that the control measurements can be started immediately. A calibration certificate is optionally available for the force gage. This certificate is a target / actual comparison on a traceable reference standard and thus serves as proof of the measurement accuracy. The measurement uncertainty of the force gage is only 0.5% of the measuring range. The force gage is therefore used as a reference device for testing and adjusting static torque tools. A screw latch is essential for dynamic torques.
The torque transducer has a 1/2″ square socket and can perform the torsion measurements in both directions of rotation. With a sampling rate of 1600 Hz, the force gage reliably detects the first and the maximum torsional moment peak (PEAK). The release moment (” click “) is shown separately in the display and can be deleted either manually or automatically after a set time has elapsed. Thanks to freely adjustable alarm values, the force gage can warn the tester of overload of the torque tool if it does not trigger itself. For a more detailed analysis of the torsional forces, the PC software included in the scope of delivery can be used.


– Left / right torsion measurement
– 1600 Hz sampling rate
– Error limit 0.5% of the measuring range
– PEAK / Hold function
– Graphic display
– PC software
– Power adapter and battery operation possible


Measuring range 0 … 100 Nm / 73.76 ft-lb
Resolution 0.1 Nm / 0.0738 ft-lb
Accuracy ± 0.5% of the measuring range
Units of measurement Nm, lbfft, kgfm
Torque sensor mount 1/2″ (12.5 x 12.5 mm) internal square
Torsion measurement Left / Right
Display 2.8″ TFT graphic display
Alarm modes Inside Outside
Sampling rate 6 … 1600 Hz
Storage For 100 measurement series with 8,000 measurement points each
Power supply NiMh battery, 6V / 1600-mAh
Battery life About 10 hours
Power supply / charging adapter 12V / 1 A
Outputs Interface: USB
Switching output: 12V / 50-mA
Protection class IP 54
Operating and storage conditions    -10 … 50°C / 14 … 122°F
5 … 95% RH non-condensing
Torque transducer dimensions H 85 mm / Ø 72 mm / Ø 104 mm (H 3.3 in / Ø 2.8 in / Ø 4.1 in)
(see technical drawing)
Sensor cable length / td> Approx. 1.5 m / 4.9 ft
Dimensions handset 200 x 97 x 42 mm / 7.9 x 3.8 x 1.7 in
Weight handset 540 g / 1.2 lbs 
Weight of the torsion transducer                                   985 g / 2.2 lbs


1 x Force Gage PCE-DFG N 100TW
1 x Torque transducer 100 Nm
1 x 1.5 m / 4.9 ft sensor cable
1 x PC software
1 x USB data cable
1 x Power supply
1 x Carrying case
1 x Sensor screw socket
1 x Instruction manual

There are no reviews yet.

Be the first to review “Force Gage PCE-DFG N 100TW”

Your email address will not be published. Required fields are marked *